Summary
Instructions for replacing the TS1500 Ethernet Adapter (p/n: CUSBNIC-2) are listed below.
Details
Unplug the stacker USB cable at the stacker. Power the entire Automated Programming System down and remove the stackers' left side upper and lower covers. Attached to the inside of the lower cover is the Ethernet adapter. Replace it. Note the revision of the old adapter: a bar code label that says S/N: xxxxxxxxxx H/W: A1, would be adapter revision A1. Other possibilities are A2, A3 and B. Note also the hardware revision of the new adapter. It will probably be rev B. Depending on the exact revision of the adapter, the cabling will be the same or slightly different. Use your best judgement to sort it out. Understand that the USB cable that plugs into the adapter, can also disconnect from the inside of the stacker if you need to replace the cable.
The network cable between the adapter and the Galil board is a crossover cable, (p/n: CCABCAT5CROSS). After connections are made, and before closing the stacker, reconnect the external USB cable that was disconnected previously, power up and see what messages are displayed. If XP asks for drivers, use the driver CD-ROM that came with the adapter. After the drivers are installed, set the IP address as per the instructions in the TS1500 Users Guide which can be found in BPWin Help. After setting the IP address, go to Device Manager and ensure that the DUB-E100 adapter is present and working properly. The LEDs on the Stacker's Galil board should be blinking.
Start BPWin and verify that the TS1500 is detected after the Serial Peripheral Scan completes. Once the stacker is communicating, be sure to replace the covers.
In the event that the TS1500 has been installed previously with a different driver, the old driver(s) must be removed. d-Link does not provide instructions to accomplish this so the instructions below were created so that customers do not have to 'reformat their hard drive' in order to install only the correct driver.
TS-1500 should be disconnected.
Press [Windows]+[Break] to bring up the System Properties dialog box.
Select the Advanced tab and click the Environment Variables button.
Click the New button below the System Variables panel.
In the New System Variable dialogue box, type devmgr_show_nonpresent_devices in the Variable Name text box and 1 in the Variable Value text box.
Click OK three times to completely exit System Properties.
Press [Windows]+[Break] to bring up the System Properties dialog box.
Select the Hardware tab and click the Device Manager button.
In Device Manager, go to View | Show Hidden Devices.
In the Device Tree expand Network adapters. Any entries that are greyed out should be uninstalled. Right-click the icon and select Uninstall. (Note: There may be 1 or 2 entries that cannot be uninstalled)
Close Device Manager and System Properties windows.
Click Start, click Run, type regedit, and then press ENTER.
View the following registry key: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services
Find DUBE100x, right-click and select Delete.
Quit Registry Editor.
Restart the computer.
Press [Windows]+[Break] to bring up the System Properties dialog box.
Select the Hardware tab and click the Device Manager button.
In Device Manager, go to View | Show Hidden Devices.
In the Device Tree expand Network adapters.
If there is an entry for D-Link adapter go to step 28.
If there is no entry for D-Link adapter plug in the TS-1500 at this time.
You should see a pop up for Found New Hardware.
Select No, not this time and Next.
Select Install from a list or specific location.
Select Search for the best driver in these locations and Include this location in the search. You will need to browse to the location of the specific driver.
Select Next, then Finish
Start BPM Microsystems software and verify that the software can see the TS-1500.
Right-click and select update driver.
Select No, not this time and Next.
Select Install from a list or specific location.
Select Search for the best driver in these locations and Include this location in the search. You will need to browse to the location of the specific driver.
Select Next, then Finish
Connect your TS-1500, Start BPM Microsystems software and verify that the software can see the TS-1500.
Related Articles
Parallel Port Driver Discontinuation
Summary Customers with BPM equipment which uses parallel ports for serial peripheral communication, Galil DMC-1040 utilizing BPM driver, AND/OR parallel programming sites will only be supported up to BPWin version 5.33.0 due to parallel port driver ...
7th Gen Stepper Motor Driver Upgrade
Over time, the need to increase device sizes and thus socket pins counts has increased, with this, some sockets require higher forces to fully open sockets. On manual systems this is not too much of a problem as the operator manually opens the ...
TS1500 - USB Communication Problem
If you are experiencing issues with obtaining communication via USB to your TS1500 tray Stacker, then please read the following information. You need to ensure that the driver is correct and that you have only one instance of DUB-E100 listed in ...
Do you have any idea of the life cycle for a socket module?
If properly cared for the socket module base, the part that connects to the programmer, should last for 10's of thousands of cycles, regardless of the package. It is important the care is taken during installation and removal of the module from the ...
TS1500 - Tray Stacker Air Pressure Error
Issue BPWin software displays a message to indicate that there is no air pressure to the tray stacker. A physical check of the air input regulators, air lines and connections shows that there is good air pressure going to Tray stacker. The error ...